|
|
||
|
 IM483I/IE Microstepping Drivers |
||
| Thermal Management | ||
| Heat Sink H-4X |
Heat sink designed to accept the IM483I and IE. | |
| Thermal Non-Isolating Pad TN-48 |
Thermal non-isolating pad consisting of aluminum foil coated on both sides with an electrically and thermally conductive rubber. One side is adhesive backed and may be applied directly to the driver. | |
| Mounting | ||
| Side Mounting Clips U3-CLP |
Clip-on mounting system for the IM483I and IE. | |
| Communications and Encoder | ||
| RS-232 to RS-485 Converter CV-3222 |
Inline RS-232 to RS-485 converter for use with the IM483I/IE Microstepping System. |
|
| RS-232 to RS-485 Converter Daughter Board OPT4-232 |
Plug-on daughter board specifically for the IM483I/IE which converts RS-232 to RS-485. | |
| Differential Encoder Input Interface Board OPT4-DE |
Differential encoder input interface board specifically for the IM483I/IE. | |
| RS-232 to RS-485 Converter and Differential Encoder Input Interface Board OPT4-232-DE |
Plug-on interface board which combines RS-232 to RS-485 conversion and differential encoder inputs on the same board. | |
| Interface | ||
| Breakout Board BB-34-4P |
Plug-on breakout board which adds screw terminal interfacing to the P1 connector end of the IM483I/IE. |
|
| Connectors | ||
| P1 and P2 Mating Connectors PLG-R |
P1 and P2 mating connectors pair for the IM483I/IE-PLG (IM483I/IE with Plug Type Terminal Strip for these connectors which are sold separately). |
|
| Replacement Connector PLG-R1 or -R2 |
Replacement connector for the IM483I/IE-PLG — P2 connector is PLG-R1; P1 connector is PLG-R2.
|
|
| GUI Software | ||
| QuickSTART 1 | QuickSTART 1 is the graphical user interface for the IM483I/IE. Also available in a 5 license site pack
(QuickSTART 1-5L). |
|
| General | ||
| IMS CD IMS-CD100-000 |
CD contains IMS Software, Product Manuals and Datasheets. | |
| IM483 Microstepping Driver |
||
| Thermal Management | ||
| Heat Sink H-4X |
Heat sink designed to accept the IM483. | |
| Thermal Non-Isolating Pad TN-48 |
Thermal non-isolating pad consisting of aluminum foil coated on both sides with an electrically and thermally conductive rubber. One side is adhesive backed and may be applied directly to the driver. | |
| Interface | ||
| Breakout Board BB-34-4P |
Plug-on breakout board which adds screw terminal interfacing to the P1 connector end of the IM483-34P1 (IM483 with 34 Position 0.025" sq Pin P1 Connector). |
|
| Connectors | ||
| P1 and P2 Mating Connectors PLG-R |
P1 and P2 mating connectors pair for the IM483-PLG (IM483 with Plug Type Terminal Strip for these connectors which are sold separately). |
|
| Replacement Connector PLG-R1 or -R2 |
Replacement connector for the IM483-PLG — P2 connector is PLG-R1; P1 connector is PLG-R2. |
|
| General | ||
| IMS CD IMS-CD100-000 |
CD contains IMS Software, Product Manuals and Datasheets. | |
| Thermal Management | ||
| Heat Sink H-4X |
Heat sink designed to accept the IM805. | |
| Thermal Non-Isolating Pad TN-48 |
Thermal non-isolating pad consisting of aluminum foil coated on both sides with an electrically and thermally conductive rubber. One side is adhesive backed and may be applied directly to the driver. | |
| Mounting | ||
| Side Mounting Clips U3-CLP |
Clip-on mounting system for the IM805. | |
| Interface | ||
| Breakout Board BB-34-4P |
Plug-on breakout board which adds screw terminal interfacing to the P1 connector end of the IM805-34P1 (IM805 with 34 Position 0.025" sq Pin P1 Connector). |
|
| Connectors | ||
| P1 and P2 Mating Connectors PLG-R |
P1 and P2 mating connectors pair for the IM805-PLG (IM805 with Plug Type Terminal Strip for these connectors which are sold separately). |
|
| Replacement Connector PLG-R1 or -R2 |
Replacement connector for the IM805-PLG — P2 connector is PLG-R1; P1 connector is PLG-R2. |
|
| General | ||
| IMS CD IMS-CD100-000 |
CD contains IMS Software, Product Manuals and Datasheets. | |
| Thermal Management | ||
| Heat Sink H-4X |
Heat sink designed to accept the IB462 and IB463. | |
| Isolating Thermal Pad TI-462 TI-463 |
The TI series of thermal isolating pad is a special film with high thermal conductivity and high dielectric strength. These pads are specifically for the IB Series drivers. |
|
| Non-Isolating Thermal Pad TN-462 TN-463 |
The TN series thermal non-isolating pad consists of aluminum foil coated on both sides with an electrically and thermally conductive rubber. One side is adhesive backed and may be applied directly to the driver. |
|
| Interface | ||
| Interface Board OPT140 |
The OPT140 adds screw terminal interfacing, isolated current reduction, 470 ohm pull-up resistors and a motor power input capacitor to the IB Series of drivers. It is solder mounted to the driver. | |
| Connectors | ||
| Snap on Terminal Strips TS-6 |
6-pin snap on terminal strips for IB Driver series, sold as a pair. | |
| General | ||
| IMS CD IMS-CD100-000 |
Contains all IMS Software, Product Manuals and Datasheets. | |
| Thermal Management | ||
| Heat Sink H-100 |
The H-100 heat sink is designed exclusively for IB104, IB106 and IB1010. |
|
| Non-Isolating Thermal Pad TN-100 |
The TN series thermal non-isolating pad consists of aluminum foil coated on both sides with an electrically and thermally conductive rubber. One side is adhesive backed and may be applied directly to the driver. |
|
| Interface | ||
| Interface Board OPT140 |
The OPT140 adds screw terminal interfacing, isolated current reduction, 470 ohm pull-up resistors and a motor power input capacitor to the IB Series of drivers. It is solder mounted to the driver. | |
| Connectors | ||
| Snap on Terminal Strips TS-6 |
6-pin snap on terminal strips for IB Driver series, sold as a pair. | |
| General | ||
| IMS CD IMS-CD100-000 |
Contains all IMS Software, Product Manuals and Datasheets. | |
| Communications | ||
| Communication Cable MX-CC100-000 |
Communication cable for the MicroLYNX System – DB-9 to 10 pin IDC. Recommended with first MicroLYNX order. |
|
| Communication Cable MX-CC200-000 |
Communication cable for 2 axis MicroLYNX SysteM – DB-9 to two 10 pin IDC. |
|
| Communication Cable MX-CC200-001 |
Communication cable for single axis MicroLYNX System mounted to an HMI – Two 10 pin IDC. Used in conjunction with MX-CC400-000 mounting kit, sold separately. |
|
| Communication Cable MX-CC300-000 |
Communication cable for 2 axis MicroLYNX System using an HMI – Three 10 pin IDC. |
|
| Hardware Mounting Kit MX-CC400-000 |
For mounting a MicroLYNX System to an HMI. Used in conjunction with MX-CC200-001 communication cable, sold separately. |
|
| Replacement Connectors | ||
| Screw Terminal MX-CN006 |
6 position screw terminal (Power, Ground and motor connections) for the MicroLYNX System. |
|
| Connector – Communications MX-CN007 |
7 position Phoenix connector (Communications). |
|
| Connector MX-CN008 |
8 position Phoenix connector, may be used on the following:
|
|
| Operating Manuals | ||
| MicroLYNX Product Manual LX-0M200-000 |
Full Manual – paper version. | |
| MicroLYNX Quick Manual LX-0M300-000 |
Quick Manual – paper version. | |
| General | ||
| IMS CD IMS-CD100-000 |
Contains all IMS Software, Product Manuals and Datasheets. | |
|
|
||
 |
||||
|
|
IMS EUROPEAN SALES MGT. 4 Quai Des Etroits 69005 Lyon, France Phone: +33 / 4 7256 5113 Fax: +33 / 4 7838 1537 E-mail: bmartinez@imshome.com. Sanderson Centre 15 Lees Lane Gosport,Hampshire, UK PO12 3UL Phone: +44 / 0 2392 520775 Fax: +44 / 0 2392 502559 E-mail: mcheckley@imshome.com |
|||
